Question & Answer: Quiz 4 (I need answers)…..

Quiz 4 (I need answers)

1) What command will be used to determine the VLAN ID that will be placed in a frame as it exits your Cisco IOS ISR interface of Gigabit Ethernet 0/1.200?
2) You have just created VLAN 7. Given the command prompt below, type the complete command to assign VLAN 7 to switch port 14.
Sw1(config)# interface Fa0/14
Sw1(config-if) #
3) Which VLAN number is the default for the Native VLAN?
4) Which three of the following should be considered when implementing VLANs?
5) Which four of the following can be verified in the output of the show interfaces trunk command?
6) Type the three letter acronym of the protocol that is used to auto negotiate trunk information between two switches.
7) Which three of the following statements are correct concerning VLANs?
8) Which command is used to ensure that a swtichport will never become a trunk.?
9) Which Inter-VLAN routing method uses a single physical link between a router and a switch?
10) Given the output below what happens to Fa0/18 if VLAN 100 is deleted?

VLAN Name                             Status    Ports

—- ——————————– ——— ——————————-

1    default                          active    Gi0/1, Gi0/2

10   VLAN0010                         active    Fa0/5, Fa0/6, Fa0/7, Fa0/8

Fa0/9, Fa0/10, Fa0/11, Fa0/12

Fa0/13, Fa0/14, Fa0/15, Fa0/16

Fa0/17, Fa0/19, Fa0/21, Fa0/22

Fa0/23, Fa0/24

100 Marketing                        active    Fa0/18

200 Engineering                      active    Fa0/20

11) Given the configuration output below, which is a trunk not forming between Sw1 and Sw2?
Sw1#show interfaces gigabitEthernet 0/1 switchport
Name: Gi0/1
Switchport: Enabled
Administrative Mode: dynamic auto
Operational Mode: static access
Administrative Trunking Encapsulation: dot1q
Negotiation of Trunking: On
Access Mode VLAN: 1 (default)
Trunking Native Mode VLAN: 1 (default)
Administrative Native VLAN tagging: enabled

************************************************************************

Sw2#show interfaces gigabitEthernet 0/0 switchport

Name: Gi0/0

Switchport: Enabled

Administrative Mode: dynamic auto

Operational Mode: static access

Administrative Trunking Encapsulation: dot1q

Negotiation of Trunking: On

Access Mode VLAN: 1 (default)

Trunking Native Mode VLAN: 1 (default)

Administrative Native VLAN tagging: enabled

12) Which of the following protocols is used in a redundant layer 2 network to eliminate a loop?
13) Given the configuration below, which of the following VLANs will be allowed across the trunk link?
Sw1(config)# interface FastEthernet 0/1
Sw1(config-if)# switchport mode trunk
Sw1(config-if)# switchport trunk native vlan 999
14) Which of the following switchport modes will successfully form a trunk between two switches?
15) Which two of the following will prevent a trunk link from being functional ?
16) Which two of the following will disable DTP on a switchport interface?
17) Which three of the following are true concerning the Native VLAN?
18) Which of the following is the purpose of a trunk between switches?
19) Which of the following commands will create VLAN 100 and name it Marketing on a Cisco IOS switch?
20) How does 802.1q identify the VLAN that the frame belongs to while it crosses the trunk link?
21) When implementing a Router on a Stick Inter-VLAN routing solution, which of the following is needed for this implementation?